FBT VERVE 212 A 2-way Bass reflex Active speaker
FBT VERVE 212 A 2-way Bass reflex Active speaker

FBT VERVE 212 A 2-way Bass reflex Active speaker

Item# VERVE-212-A

Product Description


The new Verve Speakers Series features birch plywood enclosures with a scratch resistant textured paint finish, entirely ‘Made in Italy’ and offers outstanding performance at competitive prices.

New high efficiency PWM and very light yet powerful class D integrated amplifiers, a new digital signal processor with 4 EQ presets with an extremely low noise floor. VERVE speakers are equipped with constant directivity rotatable horns, high efficiency woofers and HF compression drivers, higher quality protected crossover networks. Available in 5 bi-amplified active, 5 passive models and 2 coaxial bi-amplified stage monitors. To extend the low frequency response, VERVE speakers can be matched with FBT SUBLine subwoofers, available in 12’’, 15’’ e 18’’ models.

  • 2 x 320 mm (12”) woofer with 64 mm (2.5”) voice coil, custom made for FBT
  • 36 mm (1.4”) B&C compression driver with 64 mm (2.5”) voice coil
  • Frequency response from 50Hz to 20 kHz
  • 70°H x 50°V Constant Directivity Horn
  • 6xM10 anchoring
  • 2-way, bi-amplified, bass reflex design
  • Bi-amped: 400W RMS LF, 100W RMS HF, Class D power amplifiers
  • Digital Signal Processor with 4 Equalization Presets
  • 15 mm (0.59”) birch plywood scratch resistant enclosure and internal bracing
  • High efficiency switch mode power supply
  • Control Panel features balanced XLR/Jack input and XLR LINK OUT, Volume, EQ Presets, HP Filter, 3 status indicators
  • 15 mm (0.59”) birch plywood scratch resistant enclosure and internal bracing
  • Bi-amplified models with high dynamic Class D amplifiers 400W + 100W RMS to provide a pleasant sound even at loud volume
  • New ultra-light woofers custom made for FBT with a weather resistant coating, extremely reliable and efficient
  • High efficiency switch mode power supply
  • Advanced filter algorithms including dynamic equalization at low frequencies and advanced energy control to allow high SPL while always granting reliable and distortion-free audio reproduction
  • An increase in total SPL thanks to FBT’s new digital limiter algorithms and increased amplifier power output
  • Passive models: soft-trip high-frequency protection circuitry to ensure proper operation even in overdriven conditions and superb quality components, metallic polyester condensers and large diameter coils.
  • All components embedded in special resin to ensure total immunity to vibration
  • Fully rotatable constant directivity horn to adjust HxV angle coverage in the non-coaxial models
  • Ergonomic integrated carrying handles, M10 rigging points, top-hat speaker stand socket and wall bracket mounting hardware

New Digital Signal Processor with 4 factory equalization presets provides simple and efficient EQ adjustment. The presets have been extensively tested in the anechoic chamber to optimize the sound performance for different applications.

• ORIGINAL: is the typical ‘VERVE’ sound

• BOOST: bass and high are emphasized for a rich and engaging sound

• HI-END/ VOCAL: very fl at response, typical of the top touring systems. Provides increased intelligibility and presence for vocals and speech

• WARM: provides a full bodied response to the Low/Mid frequencies and less aggressive on the high.

Code: 35970 / W
Configuration: 2 way
Built-in amplifier LF/HF: 400 / 100 W RMS
Built-in amplifier peak LF/HF: 800 / 200 W
Frequency response: 50Hz - 20kHz -6dB
Low Frequency woofer: 2 x 230 bobina 64 inch
High Frequency driver: 36 bobina 64 inch
Maximum SPL cont/peak: 127,5 / 133 dB
Dispersion: 70° x 50° HxV
Input impedance: 22 Kohm
Crossover Frequency: 1,3 KHz
AC Power requirements: 450 VA
Input connector: XLR con loop
Power cord: 5 m/ft
Net Dimension (WxHxD): 394 x 1015 x 380 mm/inch
Net Weight: 34,5 Kg/lb
Transport Dimension (WxHxD): 495 x 1098 x 467 mm/inch
Transport Weight: 38,5 Kg/lb

Scroll to top